I am a returning customer
If you already have an account with us, please login at the login form.
Congratulations! Your new account has been successfully created!
You can now take advantage of member privileges to enhance your online shopping experience with us.
If you have ANY questions about the operation of this online shop, please e-mail the store owner.
A confirmation has been sent to the provided e-mail address. If you have not received it within the hour, please contact us.
You have been logged off your account. It is now safe to leave the computer.
Your shopping cart has been saved, the items inside it will be restored whenever you log back into your account.
Velda Pond Protector Bird and Cat Repeller
1. Place the transformer in a dry place such as a garage, maintenance room or under a roof. Secure the transformer with the additional screws provided.2. Push a metal pin into the ground in the immediate vicinity of the transformer. Make sure that th..
1. Place the transformer in a dry place such as a garage, maintenance room or under a roof. Secure the transformer with the additional screws provided.
2. Push a metal pin into the ground in the immediate vicinity of the transformer. Make sure that the metal dowel does not project more than 2 cm above the ground.
3. Connect one end of the green ground wire to the transformer's green connector, and attach the other end to the eyelet of the pin with the additional bolt and washer. If the wire is too long, you can shorten it as needed. This connection should be made at position "A" according to the illustration.
4. You can use the included synthetic stakes to install the fence around the pond. Place the pegs no more than 4 meters apart, and note that the uppermost hole of the peg should point toward the pond. The pegs should be pushed into the ground so that the bottom eye of the peg protrudes 10 cm out of the ground.
5. Thread the black electrical wire through the pegs, starting with the lowest holes. Make a knot at the end of the wire and pull the same wire through the top pegs, then make a knot at the end of the top wire as you did on the bottom wire. This connection will provide the connection between the lowest and highest wires. Stretch the wires so that the pegs do not move or come in contact with grass or other plants. The lowest wire is for keeping cats out of the pond and the highest wire is for deterring herons. This wire connection should be made at position "B" as shown in the figure.
6. Connect the red pulse wire to the red transformer socket and the other end of this wire to the lowest wire with the added connector. (position "C" in the figure)
7. When the transformer is connected to the power supply, the installation is considered complete. When the LED lamp on the transformer is turned on, the Pond Protector starts to function. You can verify the correct installation by touching the grass and feeling the electrical pulses. You can also see these pulses on the LED lamp on top of the transformer, which flashes with each pulse.
| Main | |
| Країна виробник: | Netherlands |
| Warranty: | 1 year |
| Description | |
| Color: | Black |
Ornamental crucian carp Hoe Kim is a bright stavkova fish with a distinctive red-white or red-colored barred tail and a characteristic wide tricut tail. Due to the rich color and active behavior of the fish, the fish looks very effective in a decorat..
A specialized primer for preparing EPDM and butyl rubber membranes before bonding seams with seam tapes.Polygomma Primer is a primer for EPDM and butyl rubber membranes.Polygomma Primer is a specialized primer designed to prepare the surface of EPDM ..
Special primer for the preparation of EPDM and butyl rubber membranes before gluing seams with seam stitches.Polygomma Primer - primer for EPDM and butyl rubber membranesPolygomma Primer is a specialized primer used for preparing the surface of EPDM ..
Polygomma Self-Adhesive Tape for Bonding Butaco Rubber, 7.62 cm x 30 mPolygomma self-adhesive tape is designed for bonding butaco rubber membranes and films. It is used to join sheets of material into a single, sealed web during the installation of w..
Polygomma Self-Adhesive Tape for Bonding Butaco Rubber, 7.62 cm x 30 mPolygomma self-adhesive tape is designed for bonding butaco rubber membranes and films. It is used to join sheets of material into a single, sealed web during the installation of w..
Polygomma 1mm EPDM Bottle Rubber MembraneThe 1mm Polygomma EPDM bottle rubber membrane is a reliable waterproofing material made of synthetic rubber (EPDM), designed for the construction and protection of ponds, reservoirs, and technical tanks for va..
Polygomma 1mm EPDM Bottle Rubber MembraneThe 1mm Polygomma EPDM bottle rubber membrane is a reliable waterproofing material made of synthetic rubber (EPDM), designed for the construction and protection of ponds, reservoirs, and technical tanks for va..
The Polygomma 1 mm EPDM butyl rubber membrane, 9.15 m wide, is a universal waterproofing membrane made of synthetic rubber (EPDM) designed for ponds, various reservoirs, water storage tanks, as well as for use in agriculture, fire protection systems,..